Parisa Technology

Fluorescence detector-ATP -030

Food, medicine and health, medicine, daily chemical, Papermaking, industrial water treatment, national

Defense and environmental protection, water Administration, customs entry and exit quarantine

And other, law enforcement departments and other Industries

·        The ATP rapid detector adopts special sealing material to Improve light avoidance, and the detection results are More accurate and stable.

·        Simple interface, easy to operate.

·        Bottom detection, not affected by the instrument holding or placement Angle detection data is not interfered, the result is more stable.

·        Integrated box design, convenient for travel and carrying \

·        Significantly low background values are more conducive to the detection of trace ATP, with good reproducibility, providing users with more reliable and accurate numbers.

Oxygen Permeability Analyzer Y310 2.0

 Y310 Oxygen Permeability Analyzer is designed and manufactured based on the

coulometric sensor method and conforms to GB/T 19789???ASTM D3985. This instrument can be used to measure the oxygen transmission rate of barrier materials with high and medium barrier properties with high accuracy and high efficiency. Y310 is applicable to the determination of oxygen permeability of plastic films, sheeting, paper, and other packaging materials used in food, pharmaceutical, medical apparatus, consumer products, photovoltaic and electronic industries, etc.

 Test Principle

 Y310 Oxygen Permeability Analyzer is designed and manufactured based on the

coulometric sensor method. The pre-conditioned specimen is clamped in the test cell, oxygen or air flows on one side of the specimen while a stream of high purity nitrogen flows on the other side. Oxygen molecules permeate through the specimen into the nitrogen side and are carried to the coulometric sensor. The sensor analyses the oxygen concentration and calculates the oxygen transmission rate.

 Technical Parameter

Test range:  0.05~1000 cm3/(m2·24h) ???maximum260000 cm3/(m2·24h) ???

Resolution:  0.001 cm3/(m2·24h)

Test temperature:  15~45???

Temperature resolution: ±0.1???

Test area:  50.24 cm2???Custom Adapters???minimun0.785 cm2???

Specimen Size:  Φ100 mm

Specimen thickness:  ≤3 mm

Test Cell:  3 cell

Gas Pressure:  ≥0.1 MPa

Gas Size:  Φ3 mmtube

Port Size:  1/8 Metal tube

Air pressure:  ≥0.3 MPa

Power:  750 W

Power supply:  AC 220 V???50 Hz

DIGITAL PH METER (PORTABLE, HALDHELD, PEN TYPE)

A digital potential of hydrogen (pH) meter is an electronic gadget used to accurately measure and record the pH values of liquids. Measuring pH allows one to determine the acidity or alkalinity of a substance in a liquid state.

pH is an important quantity that reflects the chemical conditions of a solution. The pH can control the availability of nutrients, biological functions, microbial activity, and the behavior of chemicals.

Measure PH and temperature
one touch automatic digital calibration.
Water resistant
Large LCD Display
Auto off function

STIRRING BATH

A powerful magnetic stirring mechanism combined with high wattage heating allows each stirring water bath to maintain temperatures to a maximum 99°C. Available in 10 and 20 litre bath capacities, these water baths comprise as many as 8 stirrers for a maximum stirring speed of 1500 rpm. Each bath includes a conspicuous front-panel LCD, reproducible microprocessor control of temperature within 0.1°C increments, a corrosion resistant stainless-steel interior and automatic alarm and safety shut down mechanism.

Note: also available multiple [le stirring position and size as per customer request

• Measures electrical conductivity (EC) and temperature. ATC- Yes, Power Source: 1X3V button cell
• Range: 0-9999 µS (µS/cm), Temp. Range: 1-80deg. Celsius/33-176deg. Fahrenheit
• Accuracy: -2% to + 2%, Calibration: Digital to any point
• Auto-off function, data-hold function and low-battery indicator. temperature reading Display: large and easy-to-read LCD screen includes simultaneous. Includes a cap and batteries.
• Size: 5.9 x 1.1 x 0.5 inches, weight: 42.5g

Brand Name: HM Digital
Colour: White
Display: Digital
Item Weight: 42.5 Gram
Material: Plastic
Measurements Accuracy: 2
Model: Plastic
Measurements Accuracy: 2
Part No: AP2
Size: Standard

AUTO GQ-300 Modified Atmosphere Refrigerator is mainly for a variety of fruits, vegetables, flowers, seedlings, etc. on the market for storage and preservation tests, through microelectronics technology to automatically control the concentration of oxygen, nitrogen, carbon dioxide, ethylene in the box, as well as control temperature, humidity conditions to achieve the preservation effect, is a microorganism, environmental protection, food production, universities, scientific research institutions and other units indispensable ideal equipment.

Product features

·       Three test chambers work independently; Each chamber has its own humidity, flow and concentration of various gases, ethylene removal devices, lighting systems, sterilization systems, and drainage systems.

 ·       Built-in microcomputer system, automatic control, automatic processing of data. Manually switch the cavity to display the temperature and humidity of each cavity, as well as the concentration of oxygen, nitrogen, carbon dioxide, ethylene and so on.

 ·       24-inch 100,000 real color touch screen, can set the parameters of each cavity and control operations respectively; Detailed data and work status are displayed in real time.

 ·       Built-in ozone sterilization, manual button sterilization, can set the sterilization time

 ·       Built-in ethylene catalytic removal device and gas displacement pump control ethylene concentration, fast degassing speed.

 ·       Imported high-precision sensors to detect various gas concentrations and ethylene concentrations.

·       The sterilization system adopts ozone sterilization, manual button for sterilization, automatic control of sterilization time, and automatic stop when the set time is reached.

 ·        Temperature control: using heating wire heating, scroll compressor cooling, stable performance, low noise; PID algorithm with solid state relay control, no hard mechanical contacts, long service life, average temperature heating, constant temperature. The temperature control of each chamber adopts unified control, and the temperature of the three chambers is set manually.

Make: HM Digital, USA

A TDS meter is a small hand-held device used to indicate the Total Dissolved Solids in a solution, usually water. Since dissolved ionized solids, such as salts and minerals, increase the conductivity of a solution, a TDS meter measures the conductivity of the solution and estimates the TDS from that reading.

RANGE : 0-9990 ppm
ATC: YES
ACCURACY: +-2%
CALIBRATION: SCREW TYPE
POWER: 2 XLR44
WEIGHT: 76.5 g

Stability Chambers are specially designed equipment for the testing of products and also to determine their shelf life such as drug, electrical components, industrial materials etc which enables you to tweak parameters like temperature,

 humidity to conduct a thorough check over varied conditions.

Temperature Range         20 ℃ to 60 ℃

Humidity Range                40%RH to 95%RH

Accuracy              +0.5 ℃ & +3.0% RH

Uniformity            +2.0 ℃ & +3.0% RH

Test Suitable for    25 ℃ & 60% RH, 30 ℃ & 65% RH 40 ℃ & 75% RH, 30 ℃ & 75% RH

Specially designed chambers for Low Humidity conditions such as 25 ℃ 40% RH, 40 ℃ & 35% RH

Insulated Chamber interior made of stainless steel with mirror/dull finish.

Exteriors with model options of Stainless steel and G.I. Powder Coating.

Illuminated Interior with full-view glass door.

Heavy-duty door hinges & latches to maintain a secure & uniform seal.

Optional:

Microprocessor Temperature controller with data logging with printer interface.

Complete with IQ, OQ, PQ & Operations & Maintenance Manual.

1 hour calibration/ 4-hour standard validation

The BOD Incubator also known as Laboratory Incubator/Bacteriological Incubator has in its acronym the following meaning; Biochemical Oxygen Demand and as its name suggests, this equipment is used to control the oxygen consumed by microorganisms while acting on the deterioration of matter. The BOD Incubator is developed for laboratories that need incubation temperature control, water quality control in relation to oxygen, pollution levels, and improvement of biology studies on insects, among others. The BOD Incubator is originally designed to incubate long-term tests of BOD (Biochemical Oxygen Demand). Due to its reliability and flexibility, it is used today in the

most diverse applications: plant growth, germination, create and maintain microbiological or cell cultures, BOD, storage of reagents, and so on.

Temperature within a range of 5°C to 60°C

Accuracy of ±0.5°C & at an uniformity of ±2°C.

Media Preparation & Culture growth at Temperatures of 22.5°C (±2°C) & 32.5°C (±2°C) have become a standard practice in any Microbiology or R&D labs

Double walled with 75mm PUF insulated, SS 304 Interior & Exterior either SS 304 or Powder Coated Stainless Steel Trays, illuminated working area, U-shaped SS tubular heaters, Forced air circulation for uniform Temperature, CFC free cooling system consisting of hermetically sealed compressor coupled with evaporation coil & condenser. Safety devices: Low & High Temperature cut-off settable thermostats.

Power supply: 230 volts 50 Hz main supply.

Optional:

Complete Operations driven through PLC with data logging capacity of upto 1000 readings, All operations through a single 4" Color Touch Screen. offline print facility, PC interface for multiple communication.

Microprocessor Temperature controller with data logging with printer interface.

Complete with IQ, OQ, PQ & Operations & Maintenance Manual.

1 hour calibration/ 4-hour standard validation

Temperature within a range of 0°C to -20/-30°C at an accuracy of ±2°C & at an uniformity of ±3°C. Double walled with 75mm PUF insulated, SS 304 Interior & Exterior either SS 304 or Powder Coated. Stainless Steel Trays, silicon door gasket, CFC free cooling system consisting of hermetically sealed compressor coupled with evaporation coil & condenser. Safety devices: Low & High Temperature cut-off settable thermostats. Power Supply: 230 volts 50 Hz main supply.

Optional:

1)    Complete Operations driven through PLC with data logging capacity of upto 1000 readings, All operations through a single 4" Color Touch Screen. offline print facility, PC interface for multiple communication

2)    Microprocessor Temperature controller with data logging with printer interface.

3)    Complete with IQ, OQ, PQ & Operations & Maintenance Manual 

Make: HM Digital, USA

A TDS meter is a small hand-held device used to indicate the Total Dissolved Solids in a solution, usually water. Since dissolved ionized solids, such as salts and minerals, increase the conductivity of a solution, a TDS meter measures the conductivity of the solution and estimates the TDS from that reading.

RANGE : 0-9990 ppm
ATC: YES
ACCURACY: +-2%
CALIBRATION: SCREW TYPE
POWER: 2 XLR44
WEIGHT: 76.5 g

Temperature within a range of 2°C to 8°C at an accuracy of ±0.5°C & at an uniformity of ±1°C. Double walled with 75mm PUF insulated, SS 304 Interior & Exterior either SS 304 or Powder Coated, Stainless Steel Trays, Illuminated working area, Forced air circulation for uniform Temperature, CFC free cooling system consisting of hermetically sealed compressor coupled with evaporation coil & condenser. Safety devices: Low & High Temperature cut-off settable thermostats

Optional:

1) Complete Operations driven through PLC with data logging capacity of upto 1000 readings, All operations through a single 4" Color Touch Screen. offline print facility, PC interface for multiple communication
2) Microprocessor Temperature controller with data logging with printer interface.
3) Complete with IQ, OQ, PQ & Operations & Maintenance Manual. 1 hour calibration/ 4 hour standard validation

ZF1800A Full-automatic Total Migration Tester.

Application:

full-automatic migration tester is applied for determination the dissolution amount of

packaging materials in different simulant soaking solutions.

1) Tableware, cans, food packaging films, tubes, etc.

2) Made from polyethylene (PE), polystyrene (PS), polypropylene (PP) or chlorinated polyvinyl

chloride (CPVC).

Evaporate and dry the soaking solutions to obtain residues migrated from the specimen. The residues analysis and weighing refer to dissolution indexes in application requirements of packaging products.

The machine conforms to guidelines GB 31604.8-2016, GB 31604.1-2015, GB/T 5009.156-2016, GB/T 9740-2008, GB/T 23949-2009, YBB 00342002-2015, YBB 00102005-2015, YBB 00082002-2015.

 Features:

 1)   Individual cooling and heating systems

2)   Built-in system of water bath

3)   Solution recycling system

4)   Nitrogen filling protection

5)   Convenient operation

6)   More security consideration

 Specifications:

 Test range:  0.2mg/dm2-167g (residue weight)/dm2

Resolution:  0.1mg/dm2

Scale parameters: Measurement range: 0~200g

Resolution: 0.1mg

Temperature control range of water bath: Room temperature~100???

Temperature control range of heating chamber: Room temperature~117.9???

Temperature control range of cooling chamber: 0~35???

Temperature precision:  ±0.5???

Chamber temperature uniformity:  ±5???

Quantity of samples:  1-18pcs (with independent test results)

Constant weighing time:  2h(conventional)

Evaporating dish volume:  0-200ml

Dimensions: Mainframe: L×W×H 178cm×93cm×145cm

Recycling system: L×W×H 120cm×88cm×170cm

Power:  220V, 50Hz, 5000W

AT2E innovative HWBC-2 Hot Wire Bottle Cutter offers an automated and cost saving way for cutting containers for section weight analysis. A clean section without deformation will be obtained by a quick cutting of bottles through heated hot wires. A precision and repeatable cutting task is easy to achieve and it’s necessary for a proper analysis.

With HWBC-2, an automatic and steady cutting process will be carried out after pressing the button. With exhaust fan and safety door design, the exhaust gas will be away from the operator during cutting.

With HWBC-2, a PET bottle could be cut up to 5 predetermined sections under a steady force and excellent section plane could be obtained. Each section will be checked to ensure that it conforms to the exact weight assigned.

Features:

• Automatic and accurate cutting process offers a very easy way of operation
• Heating power / Standby power / Cutting speed / Return speed of wire / Cutting delay are adjustable
• Energy saving design
• Durable stainless steel design
• Touching screen offers easy and user-friendly operation
• Up to 5 sections cut and suitable for up to 2 L bottle
• Safety door and exhaust fan design which exhausts gases away from the operator
• Excellent repeatability
• Adjustable supports for bottles during the cutting process
• Graduated rulers allow accurate positioning of wires

Differential pressure method Gas Permeability Analyzer N530 2.0

This product is based on the test principle of the differential pressure method, and is designed and manufactured with reference to GB/T 1038, ISO 2556 and other standards. Using high-precision pressure sensor and automatic differential pressure maintaining technology, the test accuracy is high. It is suitable for the gas permeability test of films, sheets, paper, packaging and related materials in the fields of food, medicine, medical equipment, daily chemicals, photovoltaic electronics, etc. It provides a wide range of high, medium and low gas barrier materials. , High-efficiency gas transmission rate detection.

 Test principle

 The N530 2.0 gas permeability tester adopts the principle of differential pressure method. Place the processed sample between the upper and lower chambers, use a vacuum pump to evacuate the entire gas circuit system, and then add an atmospheric pressure experimental gas to the upper chamber to form a constant pressure difference between the upper and lower chambers. Under the action of the pressure gradient, the gas permeates from the upper cavity to the lower cavity through the film, and the system can calculate the barrier performance

parameters such as the gas permeability of the sample through the pressure change of the lower cavity.

 Technical Parameter

 Testing range:  0.02~50000 cm3/(m2·24 h·0.1 MPa)

Resolution:  0.001 cm3/(m2·24 h·0.1 MPa)

Temperature control range: 15~60???

Temperature control:  ±0.1???

Degree of vacuum:  ???20 Pa

Vacuum resolution:  0.01 Pa

Test pressure:  0.1 MPa

Test gas:  O2???CO2???N2 Etc

Test area:  50.24 cm2

Sample size:  Φ110 mm

Sample thickness:  ≤2 mm

Sample Number:  3PCS

Power:  450 W

Power supply:  AC 220 V???50 Hz

Digital Rotational Viscometer

SPECIFICATIONS:

4 spindles • Spindle Guard Leg • Power Cord • Stand Set • Instruction Manual

GBDA-180 Intelligent Compost Degradation Tester.

GBDA series Intelligent Compost Degradation Tester is a high-end intelligent compost degradation test device independently developed by our company with many years of biodegradation research and development technology and application experience, using patented intelligent algorithms and adhering to the people-oriented design concept. It is currently the world's leading biodegradation analysis tester. Our company is committed to protecting our common earth home.

The test material and the inoculum are mixed and poured into the reaction kettle. Under oxygen-supply composting conditions, the organic compounds of the test materials are decomposed by microorganisms into carbon dioxide (CO2), water (H2O), mineralized inorganic salts and new-born substances of the elements contained in them, and the carbon dioxide emissions are measured by continuous infrared analysis sensors (The amount of CO2) is used to determine the final biodegradability of the test material.

GBDA series Intelligent Compost Degradation Tester, provides professional data analysis software, one-click export report function and audit trail function. It is the best equipment for manufacturers, inspection institutions, and scientific research institutes to conduct research and analysis on degradable materials.

  Features

 1) Split design

2) Novel appearance

3) Human-machine real-time interface communication

4) Cloud management

5) Data is accurate and reliable

6) Easy to operate

7) Fully automatic operation

8) Advanced technology

9) High test efficiency

10) Authority management and data tracking

Biosafety cabinets (Biological Safety Cabinet) II is a steel cabinet covered from all five sides. This cabinet is specially designed to save the user from all kinds of biological hazards. Our Biological Safety cabinets are equipped with HEPA filters and Pre-filters to provide filtered air. Environment-friendly cabinet has an easy and economical setup with a plugin-use facility. Our Class II biological safety cabinet provides a safe environment for users and products.

Most Importantly HEPA filters are used to trap the particulates & contaminated hazardous agents. These Filters are selected for the filtration of chemical powders which are manufactured according to the ASTM standards. This is the advantage given by HEPA filters and Pre-filters with air circulation in the workspace.

 Cabinet construction                   SS 304 / MS powder Coated

Cleanliness class                        ISO class 3

Atmospheric pressure                120 MMWC

Illumination level              >900 Lux

Noise pressure                         <65 decibel

Air supply filter                           Pre-Filters are Washable

Differential pressure Indicates a range         0-500 in Manometer

Differential pressure indicates the precision + 1%

Magnahelic gauge

Power supply: 230 volts 50 Hz main supply.

Optional:

Sliding door, Digital Controller, UV Germicidal lamp, UV Hour meter,